SPOON SPORTS OFFICIAL DEALER
Gaijin-Garage Homepage About Gaijin-Garage Frequently Asked Questions Contact Gaijin-Garage Place your Order

 

SEEKER OFFICIAL DEALER
 
POWER UNIT (SPOON) INTAKE / EXHAUST (SPOON) DRIVETRAIN (SPOON) CHASSIS / BODy REINFORCEMENT (SPOON)
SUSPENSION SYSTEM (SPOON) BRAKE SYSTEM (SPOON) AERO / BODY (SPOON) INTERIOR (SPOON)

■ CIVIC 1.5 TURBO FC2| FK7 (2017-ON)Parts may also suit Civic RS etc. L15B7 | L15C 1.5L VTEC TURBO, DIRECT INJECTION


POWER-UNIT
■ POWER UNIT Top of Page

■ ENGINE ACCESSORIES


PART-NUMBER

spoon OIL FILLER CAP

Extreme heat and engine vibration in Race Car can cause the OEM Plastic Cap to shake loose orSEEK even crack.
Spoon Oil Filler Cap made from High-Grade Aluminium, Expands at the same rate as your (Aluminium) Valve Cover, also has special rubber seal designed to reduce vibration transfer and hold cap in place.

ALL-15610-000 $73.58

PART-NUMBER

seeker ULTRA-LIGHT OIL FILLER CAP [RED / BLUE / BLACK / GOLD / SILVER]

The aluminum oil filler cap is subjected to a lightening to the limit while sufficient strength has been achieved ultra-lightweight (individual weight ~60g). In addition, since we have adopted a good shape of Gakari finger is very easy to open and close the cap. One part of the vehicle such as FD2 you might shaft if fitted with a front tower bar outside is a difficult opening and closing of many filler cap those of layout through the just above the filler cap, but a round bar or the like to the filler cap lightening hole It can be relatively easily opened and closed by plug. Functional design that was obtained as a result of pursuing such utility is ideal for dress-up of the engine room.
WEIGHT: ~60g
AVAILABLE IN 5 COLOURS: ■Red ■Blue ■Black ■Gold ■Silver

PART-NUMBER PART-NUMBER PART-NUMBER PART-NUMBER PART-NUMBER

OIL-CAP-XXX $89.39

PART-NUMBER

SPOON RESERVOIR TANK COVER SET [SOX] *NEW*

The last thing you want to do at the circuit is lose traction thanks to someone having dropped fluids on to the track surface, let alone drop your own fluids and contribute to the problem - Spoon Reservoir Covers slide over your Brake Fluid Reservoir and Clutch Fluid Reservoir (etc.) and are designed to catch any fluids that may be spilled under high lateral-G driving at the circuit. Also helps prevent damage to engine-bay paintwork from spillage of Fluids.
25% Cotton 75% Polyester. 1PCE.

ORG-90000-020 $13.33

PART-NUMBER

SEEKER RESERVOIR TANK COVER SET [SOX]

Fire Retardant Material. It is a safe reservoir tank cover that was manufactured in the flame-retardant material. Brake and clutch, and by using covered the reservoir tank of power steering fluid, to keep the quickly absorbed engine room boiling over of fluid to clean. The color is also the identity of the SEEKER "SEEKER orange".

PART-NUMBER

SEEK-RES-COV $16.83

PART-NUMBER

SPOON HEAT BARRIER TAPE

Oil Viscosity decreases when subjected to constant high temperatures during performance driving. The Exhaust Manifold on B-series engines routes beneath the Oil Pan in very close proximity – this can lead to extreme heat transfer from the exhaust manifold. This is evident when you remove an old Oil Pan and inspect the shallow end of the pan where the exhaust manifold is closest – you will see baked on oil residue on the inside of the pan and this is clear evidence of high heat transfer from the exhaust. Spoon Heat Barrier Tape provides a thermal barrier in between the Exhaust Manifold and the Oil Pan. We recommend application of the Heat Barrier Tape to new Spoon Baffled Oil Pans as the fresh clean surface will provide excellent adhesion when the Oil Pan is new – plus installation Is very easy when the Oil Pan is off the engine. The Heat Barrier Tape can be used on other models and components where you would want to prevent heat transfer from various components into the fluid systems etc. For example Master Brake Cylinder (and Lines), Master Clutch Cylinder (and Lines) Brake Lines, S2000 Heat Shield… In fact, the Spoon S2000 Super Taikyu Race Car uses the heat shield over the entire Firewall through to the whole length of the Transmission Tunnel etc.
Size: 200mm x 300mm 

PART-NUMBER

ALL-11200-000 $22.64

PART-NUMBER

SPOON MAGNETIC DRAIN BOLT, ENGINE

Microscopic metal fragments from the shearing of gears and wear of bearings etc. are collected by Spoon's high-power magnets.
Effectiveness of the product is immediately apparent after each oil change.
Engine Drain Bolt sold individually.

ALL-90009-001 $21.16

PART-NUMBER

SPOON MAGNETIC DRAIN BOLT SET [ENGINE + TRANSMISSION]

Microscopic metal fragments from the shearing of gears and wear of bearings etc. are collected by Spoon's high-power magnets.
Effectiveness of the product is immediately apparent after each oil change.
Set of Engine and Transmission Drain Bolts.

ALL-90009-000 $39.97

■ COOLING SYSTEM


PART-NUMBER

SPOON RADIATOR CAP [TYPE-D] FC2, FK7*

To raise the pressure of the cooling system raises the boiling point of the coolant. Spoon Radiator Caps raise the pressure to increase the efficiency of the cooling system. For the Complete Spoon Cooling System, we recomend using the Radiator Cap in combination withthe Spoon Thermo Switch, Spoon Thermostat and Spoon SEP Radiator Hoses. Please check with us for the correct type of Cap for use on your Vehicle - Type-D Caps suit newer Honda Radiators such as EG6/EG9/EG2/EK4/EK9/DC2/AP1/CL9 etc. Not suitable for use on Aftermarket radiators (please use Type-F).
SPOON: 1.35kgf/cm2
HONDA: 1.1kgf/cm2

PART-NUMBER

  $30.56

PART-NUMBER

SEEKER RADIATOR CAP [TYPE-D] FC2, FK7*

It is a high-pressure radiator cap to increase the pulling cooling efficiency boiling point of the coolant by increasing the pressure in the radiator.
This is quite useful at the time of high rotation traveling.
※ opening temperature: 1.3kgf / cm2 (normal 1.1)
1.3Kgf/cm2

PART-NUMBER

SEEK-RAD-TYPD $35.49

INTAKE-EXHAUST
■ INTAKE / eXHAUST SYSTEM Top of Page
       
PART-NUMBER

SPOON AIR CLEANER [1.5 TURBO] FK7 *COMING SOON*

Air taken at full throttle is an ultra-high speed is huge. On the other hand inertia works when the throttle OFF, the intake air is compressed in front of the throttle closed. Then the negative pressure increases more cleaner box that is sealed with reaction that is compressed and open the accelerator, so that the charging efficiency becomes. Intake system Honda NA is important and very successful as this. While reducing the resistance of the air intake, high a valid dust effect on dust of Rain, air cleaner is the best on the other hand.

17220-FK7-000 TBA

PART-NUMBER

SPOON VENTULI BIG THROTTLE BODY [1.5 TURBO] FK7 *COMING SOON*

60φ to the STD57φ, butterfly 52mm from 50mm to intake
gasket. I repeat the test review the throttle body of traditional, spoon has developed a Venturi Big throttle body as the resulting product of a higher effect. Features a diamond cutting method, to the limit reduced the inhalation resistance in order to mirror finish inside surface roughness at the same time features of the product and also increase the charging efficiency from the venturi shape as the throttle body interior surface. I adopt a large-diameter butterfly further, butterfly adopted the elliptical shape at an oblique cross section, Durability to ensure genuine equal.

16400-FK8-020 TBA

PART-NUMBER

SPOON N1 MUFFLER KIT [DUAL-N1] FK7 *COMING SOON*

Spoon N1 Muffler Kit (Catalyst-Back Exhaust System) is under development.

PLEASE NOTE: Images are of PROTOTYPE product - production verion may differ.

PART-NUMBER

18000-FK7-000 TBA

PART-NUMBER

SEEKER SUPREME EXHAUST SYSTEM [TAIL SILENCER] FK7 *COMING SOON*

Supreme Exhaust System for the 10th Generation Civic is under development.
PLEASE NOTE: Images are of Prototype exhaust - production verion may differ.
■ Dual exit layout.
■ Stainless Steel XXmm diameter piping (Catalyst-Back)
■ Blueprint Titanium finish 2-Tip Design specific to FK7 1.5 Turbo.
■ Db Rating to be announced.

SES-FK7-TAIL TBA

DRIVETRAIN
■ DRIVETRAIN Top of Page

■ TRANSMISSION


PART-NUMBER

SPOON MAGNETIC DRAIN BOLT, TRANSMISSION

Microscopic metal fragments from the shearing of gears and wear of bearings etc. are collected by Spoon's high-power magnets.
Effectiveness of the product is immediately apparent after each oil change.
Transmission Drain Bolt sold individually.

ALL-90009-002 $21.16

PART-NUMBER

SPOON MAGNETIC DRAIN BOLT SET [ENGINE + TRANSMISSION]

Microscopic metal fragments from the shearing of gears and wear of bearings etc. are collected by Spoon's high-power magnets.
Effectiveness of the product is immediately apparent after each oil change.
Set of Engine and Transmission Drain Bolts.

ALL-90009-000 $39.97

CHASSIS / BODY REINFORCEMENT
■ BODY REINFORCEMENT Top of Page

SUSPENSION
■ SUSPENSION SYSTEM Top of Page


■ RIGID COLLAR™ リジカラ


PART-NUMBER

RIGID COLLAR [FRONT] FK8, FK7, FC1, FC2, FC3 *NEW*

RIGID COLLAR™ is an original part developed by SPOON to increase vehicle body rigidity by connecting the sub-frame components to the monocoque. When vehicles are manufactured in the factory, many components are given oversized bolt recesses (holes) to allow for fast and easy installation on the assembly line. The components are aligned and tightened to specification and the vehicle is ready for the consumer. Instantly that any new car is driven, it becomes subject to shocks and vibrations which place force on all components and can create movement and even distortion resulting in compromised function of the individual components of the vehicle. Over time and mileage, these components are subjected to a compounding effect of these forces and this can lead to increased vehicle harshness and even component failure in extreme circumstances. The different materials that these individual components are made from also presents uneven wear and distortion additionally contributing to subframe and component movement.

■ 12 PCE

50261-FK8-000 $209.14

PART-NUMBER

RIGID COLLAR [REAR] FK8, FK7, FC1, FC2, FC3 *NEW*

RIGID COLLAR™ is an original part developed by SPOON to increase vehicle body rigidity by connecting the sub-frame components to the monocoque. When vehicles are manufactured in the factory, many components are given oversized bolt recesses (holes) to allow for fast and easy installation on the assembly line. The components are aligned and tightened to specification and the vehicle is ready for the consumer. Instantly that any new car is driven, it becomes subject to shocks and vibrations which place force on all components and can create movement and even distortion resulting in compromised function of the individual components of the vehicle. Over time and mileage, these components are subjected to a compounding effect of these forces and this can lead to increased vehicle harshness and even component failure in extreme circumstances. The different materials that these individual components are made from also presents uneven wear and distortion additionally contributing to subframe and component movement.

■ 12 PCE

 50300-FK8-000 $209.14

BRAKE SYSTEM
■ BRAKE SYSTEM Top of Page

PART-NUMBER

SPOON 6-POT FuLL-MONOCOQUE CALIPER SET FK7, FC2 *COMING IN 2017*

New Spoon 6-Piston Full-Monocoque Calipers are presently undergoing testing and will be available in 2017.
ROTOR SIZE: 294-320mm

PART-NUMBER

45020-XXX-000 TBA

PART-NUMBER

SPOON LONG HUB BOLT [EACH]

The standard Hub Bolts will only allow for use of a 5mm spacer maximum. Spoon Long Hub Bolts are +8mm longer than standard hub bolts to allow use of Wheel Spacers without compromise of the length of the thread the Wheel Nut has to bite. Recommended for use when installing Spoon Brake Calipers to enable use of Wheel Spacers to promote Caliper to Spoke clearance of Wheels.
Hub Bolt, Each.
SPOON: 52mm
HONDA: 44mm

90113-EK9-000 $8.71

PART-NUMBER

SPOON LONG HUB BOLT [SET, 20]

The standard Hub Bolts will only allow for use of a 5mm spacer maximum. Spoon Long Hub Bolts are +8mm longer than standard hub bolts to allow use of Wheel Spacers without compromise of the length of the thread the Wheel Nut has to bite. Recommended for use when installing Spoon Brake Calipers to enable use of Wheel Spacers to promote Caliper to Spoke clearance of Wheels.
Hub Bolt, Set of 20.
SPOON: 52mm
HONDA: 44mm

90113-EK9-000 $174.16

PART-NUMBER

SEEKER WIDE TREAD SPACER [5mm] EK9, EP3, FN2, FD2, DC2, DC5, AP1, AP2, ZF1

5mm Spacer 2PCE. 4x114 / 5x114. Aluminum is a die-cast of 5mm thickness wide tread spacer.
It was to minimize the camera shake by setting a high degree of accuracy and high strength and Honda vehicles only size the hub diameter (except one part of the model).
It will be the hub diameter 64m P.C.D 114.3 4 hole / 5 hole multi-type two 1SET.

SEEK-SPACER-5MM $50.32

■ BRAKE ROTORS


PART-NUMBER

SPOON BRAKE ROTOR, FRONT [mm] FC2

It is dedicated to the brake rotor of 6-Piston caliper installed.
Specifications TBA.

TBA TBA

PART-NUMBER

SPOON BRAKE ROTOR, FRONT FC2

Specifications TBA.

TBA TBA

PART-NUMBER

SPOON BRAKE ROTOR, REAR FC2

Specifications TBA.

TBA TBA

■ BRAKE PADS


PART-NUMBER

SPOON BRAKE PAD [FRONT] FC2

Spoon Brake Pads are designed for performance use with improved pad-wear (and Rotor wear) at the Circuit and resistance to Fade under high-temperature use.
Recommended for Track use however can be used on Street by confident and competent drivers.
Operating Temperature Range: 0 ~ 400 ℃
Friction Coefficient: 0.32 to 0.38
Pad Material: Non-Asbestos-Based hardening type

45022-FC2-000 TBA

PART-NUMBER

SPOON BRAKE PAD [FRONT] FK8 - BREMBO CALIPER

Spoon Brake Pads are designed for performance use with improved pad-wear (and Rotor wear) at the Circuit and resistance to Fade under high-temperature use.
Recommended for Track use however can be used on Street by confident and competent drivers.
Operating Temperature Range: 0 ~ 400 ℃
Friction Coefficient: 0.32 to 0.38
Pad Material: Non-Asbestos-Based hardening type

45022-FK8-000 TBA

PART-NUMBER

SEEKER BRAKE PAD - TYPE C [FRONT] FK8 - BREMBO CALIPER

Seeker Type C Brake Pads are a high-performance pad tested in circuit racing conditions.
Carbon-Metal compound provides excellent braking force and resistance to fade with high durability and abrasion resistance. Can be used on the street by confident drivers.

Recommended for Circuit Use, Operating Temperature 0℃ ~ 700 ℃

SEEK-TYPE-C-FK8F TBA

PART-NUMBER

SEEKER BRAKE PAD - TYPE C [REAR] FK8

Seeker Type C Brake Pads are a high-performance pad tested in circuit racing conditions.
Carbon-Metal compound provides excellent braking force and resistance to fade with high durability and abrasion resistance. Can be used on the street by confident drivers.

Recommended for Circuit Use, Operating Temperature 0℃ ~ 700 ℃

BPAD-TYPE-C-FK8R TBA

PART-NUMBER

SEEKER BRAKE PAD - TYPE C [FRONT] FC2

Seeker Type C Brake Pads are a high-performance pad tested in circuit racing conditions.
Carbon-Metal compound provides excellent braking force and resistance to fade with high durability and abrasion resistance. Can be used on the street by confident drivers.

Recommended for Circuit Use, Operating Temperature 0℃ ~ 700 ℃

SEEK-TYPE-C-FC2F TBA

PART-NUMBER

SEEKER BRAKE PAD - TYPE C [REAR] FC2

Seeker Type C Brake Pads are a high-performance pad tested in circuit racing conditions.
Carbon-Metal compound provides excellent braking force and resistance to fade with high durability and abrasion resistance. Can be used on the street by confident drivers.

Recommended for Circuit Use, Operating Temperature 0℃ ~ 700 ℃

BPAD-TYPE-C-FC2R TBA

PART-NUMBER

SEEKER BRAKE PAD - TYPE E [FRONT] FK8 - BREMBO CALIPER

Seeker Type E Brake Pads are an entry-level pad that is affordable and suitable for use on the Street and under Sports driving conditions. Reaches operating temperature quickly. Minimal dust production.

Suitable for Street/Sports Use, Operating Temperature 0° ~ 600°

SEEK-TYPE-E-FK8F TBA

PART-NUMBER

SEEKER BRAKE PAD - TYPE E [REAR] FK8

Seeker Type E Pads are an entry-level pad that is affordable and suitable for use on the Street and under Sports driving conditions. Reaches operating temperature quickly. Minimal dust production.

Suitable for Street/Sports Use, Operating Temperature 0° ~ 600°

SEEK-TYPE--FK8R TBA

PART-NUMBER

SEEKER BRAKE PAD - TYPE E [FRONT] FC2

Seeker Type E Brake Pads are an entry-level pad that is affordable and suitable for use on the Street and under Sports driving conditions. Reaches operating temperature quickly. Minimal dust production.

Suitable for Street/Sports Use, Operating Temperature 0° ~ 600°

SEEK-TYPE-E-FC2F TBA

■ BRAKE HOSES


01460-FK8-000

SPOON BRAKE HOSE SET FC2, FK7, FK8 *COMING SOON*

Spoon developed their high-strength Brake Hose Set to take the abuse of Circuit Use and Endurance Racing where the demands on the brake hydraullic system are extreme. Resistant to flex and heat, The Spoon Hoses will improve pedal feel and piston pressure and are an excellent upgrade for both Stock Brake Equipped vehicles an Big Brake Kits alike.
Spoon Brake Hose Set are made from high-strength Braided Stainless Steel Hose with inner Teflon coating for minimal resistance.

01460-FK8-000 TBA

PART-NUMBER

SPOON BRAKE PEDAL BOX FK8

Based on New Genuine Honda Brake Pedal Assembly, Spoon strengthens, boxes and re-inforces the arms to prevent any flex or fatigue through extreme motorsport use.
Dramatically improves the reliability of the brake control and promotes pedal stiffness.

46600-FK8-000 TBA

AERO / BODY / EXTERIOR
■ EXTERIOR Top of Page

■ STICKERS / DECALS


'VTEC TURBO' Decal Sticker Genuine 75717-TGH-C01

'VTEC TURBO' DECAL [GENUINE HONDA] FK7, FC3, FK8

Genuine Honda 'VTEC TURBO' decal set for use on rear windscreen glass.

■ Includes template for easy alignment during installation
■ JDM Honda Genuine Accessory

75717-TGH-C01 XXXX

PART-NUMBER

SPOON WINDSHIELD BANNER

Spoon Windshield Banner is a functional and stylish upgrade. For fitment of Roll-Cage, the Sun-Visors must be removed for cage-clearance. The Spoon Banner replaces the function of the Window visors and can be trimmed to suit individual vehicle or personal requirments. Also weight saving through removal of window visors is a benefit.
Width: 185 x Height: 1450mm.

INSTALLATION TIPS:
- Wash car normally.
- Clean windscreen with Wax/Grease Remover.
- ISO Alcohol Wipe. - mix 1 droplet detergent with 2/3 Water 1/3 methylated spirits into Spray squirter.
- Squirt glass under banner. - Position Banner.
- Squeegee Water and Bubbles out.
- Trim edges with blade.
- Leave to dry in sun 1 Hour.

ALL-90000-000 $63.13

PART-NUMBER

SPOON REAR WINDOW STICKER, BLACK [800mm]

Spoon Rear Window Sticker as used on the Spoon Race and Demo Cars since ~1987.

ALL-90000-B02 $37.88

PART-NUMBER

SPOON REAR WINDOW STICKER, WHITE [800mm]

Spoon Rear Window Sticker as used on the Spoon Race and Demo Cars since ~1987.

ALL-90000-W02 $37.88

PART-NUMBER

SPOON DOOR STICKER, BLACK [300mm]

Spoon 300mm Sticker for use on door, under the mirror.

ALL-90000-B01 $18.94

PART-NUMBER

SPOON DOOR STICKER, WHITE [300mm]

Spoon 300mm Sticker for use on door, under the mirror.

ALL-90000-W01 $18.94

PART-NUMBER

SPOON TEAM STICKER, BLACK [200/100mm]

Spoon 200mm Sticker for exterior use (Tail Gate etc).
Includes bonus 100mm Sticker perfect for use on Helmets, ECU Cover etc.

ALL-90000-B00 $17.42

PART-NUMBER

SPOON TEAM STICKER, WHITE [200/100mm]

Spoon 200mm Sticker for exterior use (Tail Gate etc).
Includes bonus 100mm Sticker perfect for use on Helmets, ECU Cover etc.

ALL-90000-W00 $17.42

PART-NUMBER

SPOON-SPORTS STICKER [BLACK] *NEW*

New School Spoon Sports Logo Sticker - us used on doors of modern Honda vehicles such as Fit GK5, CRZ, S660 etc.
H40mm x W250mm.

ALL-90000-B21 $18.94

PART-NUMBER

SPOON-SPORTS STICKER [WHITE] *NEW*

Spoon 200mm Sticker for exterior use (Tail Gate etc).
Includes bonus 100mm Sticker perfect for use on Helmets, ECU Cover etc.
H40mm x W250mm.

ALL-90000-W21 $18.94

PART-NUMBER

SPOON MARK STICKER SET [TSURU]

Spoon Mark Sticker Set - featuring the famous Spoon 'Tsuru' logo, based on the famous 'Spoon Curve' at Suzuka Circuit.
Each set icludes:
2 x Large Stickers - for use on Rear Bumper above Exhaust Tip.
3 x Medium Stickers - for use on Doors.
3 x Small Stickers - perfect for use on Helmets etc.

ALL-90000-T10 $13.93

PART-NUMBER

TYPE ONE MARK STICKER

Type One Mark Sticker - as used on Spoon Carbon Spoiler and other places.

ALL-90000-T01 $8.71

PART-NUMBER

TYPEONE LOGO STICKER *NEW*

New School Type One Sticker, die-cut vinyl style for use on Door etc.

ALL-90000-T21 $18.29

PART-NUMBER

TEAM SEEKER METAL STICKER [PLAQUE]

It is the official sticker of SEEKER.
It will be the specification feeling of luxury that has put the color in anodized aluminum metal plate.
Exterior is possible of course also attached easily into the interior of the dashboard and the like.
This sticker is the hope in the opportunity to make more of the communication field.

Plaque Style, Size: 100x36mm

SEEK-TEAM-PLAQ

$17.04


PART-NUMBER

SEEKER EMBLEM [BADGE]

Chrome Badge perfect for use on Bootlid / Tailgate or Dashboard.
SEEKER logo is a three-dimensional design and emblem which has been subjected to luxurious black chrome plating process. Black chrome has presence is rich in expression and or black out or shining dazzlingly by the angle at which the light hits. *Bright Chrome no longer available.
160mm x 18mm

PART-NUMBER PART-NUMBER

SEEK-EMBLEM $62.44

PART-NUMBER

SEEKER LOGO STICKER [S] 150mm

150mm Sticker. WHT/SILV/BLK

 

SEEK-LOGO-S $17.04

PART-NUMBER

SEEKER LOGO STICKER [M] 300mm

300mm Door Sticker (Black).

 

SEEK-LOGO-M $28.39

PART-NUMBER

SEEKER LOGO STICKER [L] 800mm

800mm Rear Window Sticker (White).

 

SEEK-LOGO-L $68.15

PART-NUMBER

SEEKER HELMET VISOR STICKER

It is a competition style sticker pasted on the visor of the helmet. Front view of the part that is a sticker pasted on to be printed on the punching material of the sticker also we have secured.
You can use to cut according to the visor shape.
Width: ~435mm

PART-NUMBER PART-NUMBER

SEEK-VISOR $65.22

■ AERO / BODY


PART-NUMBER

SPOON CARBON LIP SPOILER FK8, FC2

Carbon material is superior in strength, since addition is a lightweight, it has been adopted in different parts in the world of motor sports, and has a unique texture. Mounting, attach it to remove the front lower skirt of STD.
Requires Spoon Lip Spoiler Bolt Set (Mounting Hardware).

71110-FK8-000 TBA

PART-NUMBER

SPOON CARBON LIP SPOILER FK8, FC2

Carbon material is superior in strength, since addition is a lightweight, it has been adopted in different parts in the world of motor sports, and has a unique texture. Mounting, attach it to remove the front lower skirt of STD.
Requires Spoon Lip Spoiler Bolt Set (Mounting Hardware).

71110-EKA-000

TBA


PART-NUMBER

SPOON CARBON BONNET FK7 *COMING SOON*

Carbon material is superior in strength, since addition is a lightweight, it has been adopted in different parts in the world of motor sports, and has a unique texture. Bonnet, lighter about 1/2 to 8.2kg from 15.5kg normal EG, EK in the system. It is to the same effect as the air conditioning is not installed. To reduce understeer, this weight reduction, will exhibit good handling characteristics essential to sports driving mitigation of the burden of turning a quick, to the brake, and improved acceleration performance in FF car front heavy. Product has made use of texture of black carbon fiber Lacey. The mounting method in the same lock and STD, hood pin is not required. I will also work such as window washer.

PLEASE NOTE: Images are of PROTOTTYPE product - production verion may differ.

60100-FK7-000 TBA

PART-NUMBER SPOON CARBON ROOF SPOILER FK8, FC2 68800-FK8-000 TBA

■ MIRRORS


PART-NUMBER

SPOON AERO MIRROR FK8, FC2

Spoon Aero Mirrors developed for minimal drag and stylish looks. Made from FRP with gel-coating, featurin Spoon Hydro Blue Mirrors (300R).

 

76100-FK8-000 TBA

PART-NUMBER

SPOON HYDRO-BLUE WIDE MIRROR FK8, FC2

Spoon Mirrors install over the existing standard wing mirrors featuring 900R Curvature for increased field of view with low-distortion.
Titanium Oxide Optical Coating provides a photocatalytic effect to reduce glare / dazzling effect from the lights of other vehicles and reduce driver fatigue.
Hydrophilic Blue coating is also water and dirt resistant.

76203-FK8-020 TBA

■ WHEELS


PART-NUMBER

SW388 [18x8.5" +45 5H114.3] FC2, FC3, FK7, FN2, FD2, CL7 *NEW*

Spoon began development of the World's ligthest aluminium wheel in partnership with Desmond Corporation in 1994. After 2 years of development to achieve the weight of 3.88KG per 15" Wheel, the original SW 388 was released in 1996. Production ended in 1999 with the closing of the Russion Press Factory.
Due to popular demand from our Customers, Spoon has now developed a revised wheel taking into consideration strength, weight, calper clearance and modern sizes/specs. Spoon worked from the original drawings and designer of the SW 388 from 1994, keeping the style of the orioginal wheels combined with modern manufacturing processes and higher-grade materials to bring you a wheel that is superior.

■ ANTHROCITE BLACK (Anodized Matte Black) the traditional Spoon finish is ligther and stronger than Paint.
■ MADE IN JAPAN by Taneisya.
■ Manufactured by Forge Cutting Mthod for maximum strength and minimum weight.
■ Contoured Hub-Face - Groves cut on mounting face of the wheel provides natural even load dispersion to the hub, and improves the fastening strength to the Wheel. This reduces the burden of shock absorbtion through the hub and knuckles. By being pulled outwards, the accuracy of the central axis after installation is increased. Also designed to prevent losening of the hub-Bolts.
■ Centre cap is NOT included - sold separately 42703-CP01-BK.
■ Accepts Spoon 6-Piston Caliper without spacer.
■ 18”8.5J+45 5H114.3 Specifically for 10th Generation (2017-on) Civic 1.5T with 5x115.3 PCD.

PART-NUMBER PART-NUMBER

42703-1885-45

EMAIL US


PART-NUMBER

CENTER-CAP [SW388] ALL *NEW*

Spoon Sports Centre Cap for use with SW388 wheels.

■ Features Spoon Sports Logo.
■ Center Bore 67mm.

42703-CP01-BK

$26.57
(each)


INTERIOR ACCESSORIES
■ INTERIOR Top of Page

PART-NUMBER

SPOON BLUE WIDE REAR VIEW MIRROR FK8, FC2

Spoon Mirrors install over the existing standard mirror featuring 14000R Curvature for increased field of view with low-distortion - Basically the same field of view as a 'Broadway' mirror with just the small compact size of the standard mirror body.
Titanium Oxide Optical Coating provides a photocatalytic effect to reduce glare / dazzling effect from the lights of other vehicles and reduce driver fatigue.

76400-BRM- TBA

PART-NUMBER

SPOON STEERING WHEEL [340mm]

Spoon Steering Wheel is manufactured by Momo Italy utilising an unique rim contour and 340mmm diameter specifically designed for maximum grip under race conditions - especially suited for FF vehicles with extreme 'kick-back'. Covered in the highest quality Itallian leather with Red-stitching.
Includes Spoon Horn Button (not sold separately).

ALL-78500-000 $407.52

PART-NUMBER

SEEKER RACING SPEC STEERING WHEEL [350mm] FK7 *COMING SOON*

Seeker Racing spec Steering Wheel for the 10th Generation Civic is under development. It is Kodawari of the steering wheel in pursuit of the sport driving, including race, and the like. 

PLEASE NOTE: Images are of PROTOTYPE product - production verion may differ.

■ 350mm diameter with thick rim contour for maxiumum grip.
■ Red-accent design to match Interior styling of Civic Type R FK8.
■ Frame made from high rigidity and a 6061 aluminum alloy
■ Luxurious perforated Leather
■ Red cross-stitching
■ 'R-SPIRIT' Horn Button included.
■ 'SEEKER' Logo embroidered at 6 o'clock.

PART-NUMBER PART-NUMBER

SEEK-S-WHEEL-350 TBA

PART-NUMBER

SPOON STEERING BOSS [SRS-DELETE] FK8, FC2

Spoon Steering Boss Kits are die-cast aluminium units designed for minimal weight and maximum strength.
Suitable for use with Spoon, Momo and Nardi wheels.
Includes SRS Delete Harness to eliminate the Airbag Warning Light.
Includes Steering Wheel Bolts (Allen style).

78512-FK8-000 TBA

■ SEATS / SEAT RAILS


PART-NUMBER

SPOON CARBON BUCKET SEAT

Spoon Racing Carbon Bucket Seats are designed to hold the driver firmly into place in the perfect driving position. Ultra lightweight Carbon Fibre construction, weighing in at only 5.7Kg, this is the ultimate Racing Seat for your Honda. Designed to reduce driver-fatigue through long races.

■ Weight ~5.7Kg.
■ Recommended to use with Spoon Aluminium Side Stay (Braket).

ALL-81100-000 $1,502.09

PART-NUMBER

SPOON ALUMINIuM SIDE STAY [FOR SPOON CARBON BUCKET SEAT]

Spoon Seat Bracket for use with Spoon Carbon Bucket Seats (Side-Mount).

■ Side-Mount Seat Bracket for use with Spoon Carbon Racing Bucket Seat.
■ For use with Seeker / Bride or Recaro Rails without side stay - for example Type-RO,RB. Drill Rail and fix with bolt.
■Includes Mounting hardware.

PART-NUMBER PART-NUMBER

ALL-81100-B00 $290.47

PART-NUMBER

SEEKER x BRIDE FULL BUCKET SEAT [FRP]

It is a full bucket seat of the collaboration model of the BRIDE boasts a high rigidity and excellent hold of. The underlying shell has adopted the VIOS3 with the most matches easily seat position as much as possible down easy structure in Japanese type (Low MAX).
Shoulder support is somewhat smallish because, wearing indoor space to narrow a S2000 is also available.
This collaboration model inherits the design of the predecessor full bucket seat that had gotten popular, adopt a skin fabric red and black two-tone specification.
The BRIDE sheet somewhat strong competition image by the headrest further subjected to a dedicated logo embroidery to add a bright red stitch performance is intact, we have succeeded in that to be transformed into optimal fashionable to street youth It was.
BRIDE-made seat back protector in this product (black) is standard equipment.
Seat rail (sold separately) is a vehicle inspection also safe because it becomes a security standard conform if you can use in combination with made BRIDE.
Please feel free to contact us so we will also sell BRIDE seat rail.

Note: If you are attached to the S2000 has a case where BOX lid portion that housed the trunk opening and closing the switch can not be to interfere with the fully open to the sheet. In each case there is no problem if it is possible to slide the seat forward.

■ Specifications
Shell: FRP Silver Shell (VIOS3-based)
Skin fabric: Black & Red logo dedicated logo and dedicated Red stitch Add
Sheet weight about 7.1kg (not including the seat rails)

SEEK-BRID-FRP $1,248.82

PART-NUMBER

SEEKER SEATBELT WARNING CANCELER [ALUMINIUM]

Eliminates seatbelt warning light when using harness at the circuit / motorsport. Simply plug in to your stock seatbelt plug while you are not using the standard sash-belts.

PART-NUMBER

SEEK-BELT-ALU $33.55

■ SHIFT KNOBs


PART-NUMBER

SPOON SHIFT KNOB, ALUMINIUM [6MT]

Spoon Alloy Shift Knob is the same countour as the Duracon however it is a little heavier at ~130g.
Includes 6MT Shift Patten Decal.
Includes Locking grub-screw and Allen wrench.
10mm  / 1.5mm

ALL-54102-002 $52.90

PART-NUMBER

SPOON SHIFT KNOB, DURACON [6MT]

Spoon Duracon Shift Knob is made from a special Heat-Resistant Thermo-Plastic - perfect to resist heat-soak from the transmission and exhaust and heat from direct sunlight and Summer cabin temperatures. Lightweight design at just ~80g
Includes 6MT Shift Patten Decal.
Includes Locking grub-screw and Allen wrench.
10mm  / 1.5mm

DURACON® is a crystalline thermoplastic acetal copolymer. The primary raw material trioxane, a trimer of formaldehyde.
The thermoplastic adopts a copolymer structure in which polyoxymethylene (-C-O) and carbon-carbon (-C-C- bond) comonomer groups are incorporated into its main chain. Therefore the copolymer has superior chemical and thermal stability, compared with acetal homopolymer. Acetal co-polymer is well-balanced in terms of mechanical, chemical and thermal properties, and its superior moldability allows it to be widely employed in various industrial fields.
Source: PolyPlastics.

ALL-54102-003 $52.90

PART-NUMBER

SEEKER HEAVY SHIFT KNOB 400g [6MT] EP3, DC5, FN2, FD2, AP1, AP2, ZF1

Same shape and size as Honda genuine shift knob - spherical type.
It was it possible to reliably shift work as well as to achieve a very moist and shift feel from its weight. Further, in order to perform a shift operation using the weight of 400g, it is gentle to be characterized for the respective gears.
We were greatly improved wear resistance and oxidation resistance subjected to TiAlN (titanium aluminum nitride coating) process on the surface. Furthermore SEEKER logo and shift patterns ( 6MT) to the top part we laser etching. Distinctive color and texture with the TiAlN, and enjoy the feel of heavyweight Come. ■ stainless steel surface treatment: TiAlN (titanium aluminum nitride coating). Weight: about 400g 5MT dedicated Honda genuine nuts separately if ■ genuine knob of car not a nut fixed You will need.

SEEKER: 400g (Stainless Steel)
STOCK: ~140g (Aluminium)

SEEK-SHIFT-6MT $120.94

PART-NUMBER

SEEKER SHIFT BOOT COLLAR FN2, FD2, DC5, CL7, CL9, GE8, GK5, ZF1, FK2, FK8

Machined aluminium shift boot collar for use with aftermarket gearknobs on modern Hondas.

For CR-Z · S660 of GE-FIT and GK-FIT and 1 parts of which have taken a system that connects the shift boot and genuine knob, not good appearance when combined with external shift knob. This is especially recommended for the appropriate type of vehicle so you can improve the aesthetics in that you use this shift boot color.
In addition, since we have a standard feature an O-ring on the inside of the boot color, it is easily possible to set the vertical position of the color.
It also prevents abnormal noise which is generated by the vibration of the engine.

And removing the genuine color is easy mounting of only tighten this product with the supplied tie wrap.

PART-NUMBER

SHIFT-BOOT-COL $28.39
 
 
 

■ Prices listed are in AUD - Gaijin-Garage can only accept payment in the form of AUD (Australia Dollars).
■ Item pricing correct as at August 1st, 2016 (nominal exchange rate of 78.00JPY/1AUD). Prices listed are subject to change without notice. Gaijin-Garage aims to bring you the Spoon Sports and Seeker product ranges at the best possible prices however, increases of the cost of business, fluctuations in exchange rates, changes to shipping and manufacturing costs, taxes and duties applied (and other factors beyond our control) may result in price changes. When possible, Gaijin-Garage will try to absorb these costs and attempt to avoid passing them on to the Customer. Gaijin-Garage will inform the Customer of any change in price prior to finalising any orders or shipment.
■ Items that have been hand-delivered or picked up by the Customer are still subject to shipping charges and relevant taxes.
■ International Orders are exempt from GST (Australian sales tax) however any taxes or duties incurred at the Cutomer's destination country are the responsibility of the Customer. Goods received into Australia may be subject to taxes and duty on entry to Australia - these fees may apply to international orders however sales-tax on the purchase itself is exempt.
■ Gaijin-Garage are not responsible for any typographical errors in product pricing or technical specifications (etc.) listed on this website or on any other material.
■ Product descriptions have been translated from Japanese, some descriptions may be a direct software translation - please contact us for any clarification.
■ Discontinued parts listed for reference purposes only - These parts are no longer in production and therefore not available for purchase.
■ PLEASE READ OUR TERMS AND CONDITIONS FOR MORE INFORMATION.

 
#95 Spoon Race Car News
Click Here to return to the Gaijin-Garage Homepage  
   
■ Spoon-Sports
■ Seeker
■ Rigid Collar™
■ Honda Genuine
■ Modulo / Access
■ Email sales@gaijin-garage.com
■ Phone +61 422 519 108
■ Facebook
■ Instagram
■ Youtube
 
© Gaijin-Garage 2016. Disclaimer | FAQ | Top of Page
PayPal - Verified Trader
リジカラ RIGID COLLAR Australia